Which disc should I choose for which operation?

For cutting through material, use a cutting disc; for removing material, a grinding disc; for levelling and finishing welds, a flap disc; and for cleaning and conditioning a surface, a Hilblend blending disc.

The four types at a glance

TypeOperationSuitable for
Flat cutting discCuttingSteel and stainless steel
Depressed centre cutting discCutting with depressed centreSteel and stainless steel
Grinding discRemoving materialSteel and stainless steel
Flap discLevelling, deburring and finishingSteel, stainless steel and aluminium
HilblendCleaning and conditioningSteel, stainless steel and aluminium

How the types differ

Cutting discs are thin, from 1.0 to 3.0 millimetres, and are intended to cut through material. Grinding discs are thicker, usually 6.4 millimetres, and are intended to remove material. Both consist of abrasive grains bonded with resins and fillers and reinforced with glass fibre.

Flap discs work differently. They consist of overlapping flaps of abrasive cloth. The zirconia grain breaks down in a controlled way during use, constantly creating new sharp cutting edges. As a result, performance remains consistent over the life of the disc. HILCO flap discs have a conical design on a fibre backing pad, intended for grinding at an angle of 15 to 25 degrees.

The Hilblend blending disc is made of thick synthetic fibres with an extra coarse grain. The open structure cuts fast without clogging. The disc removes, levels and conditions in a single operation, without removing excessive base material.

Typical applications

  • Removing surface rust, corrosion and mill scale with Hilblend
  • Removing light weld spatter and contamination without affecting the plate
  • Removing paint and epoxy coating in preparation for a next operation
  • Levelling welds and bevelling edges with a flap disc
  • Removing burrs after cutting

What to consider when choosing

Pay attention to the diameter, the thickness and the bore size, so that the disc fits your machine. Also check that the disc is suitable for the material you are working on. With stainless steel, it is important that the disc does not leave ferrous contamination, because that can later cause rust.

Where the discs are used

Abrasives are used in virtually every sector where metal is worked. In the petrochemical industry, the food industry, shipbuilding, construction and repair and maintenance, they are part of daily work. They are often used in combination with welding: first cutting, then welding, then levelling and finishing the weld.

In hardfacing, a disc is even part of the process. The weld metal of hardfacing products is so hard that it can only be finished by grinding. Turning or milling is not possible. Allow for this in your work preparation.

HILCO Hildiscs are produced in the Netherlands. The complete documentation can be found under abrasives documentation.

We are happy to help you put together the right range of discs for your workshop.

Contact

Do you have a question? Feel free to contact us using this contact form!

  1. Which disc should I choose for which operation?
    "

    For cutting through material, use a cutting disc; for removing material, a grinding disc; for levelling and finishing welds, a flap disc; and for cleaning and conditioning a surface, a Hilblend blending disc.

    The four types at a glance

    TypeOperationSuitable for
    Flat cutting discCuttingSteel and stainless steel
    Depressed centre cutting discCutting with depressed centreSteel and stainless steel
    Grinding discRemoving materialSteel and stainless steel
    Flap discLevelling, deburring and finishingSteel, stainless steel and aluminium
    HilblendCleaning and conditioningSteel, stainless steel and aluminium

    How the types differ

    Cutting discs are thin, from 1.0 to 3.0 millimetres, and are intended to cut through material. Grinding discs are thicker, usually 6.4 millimetres, and are intended to remove material. Both consist of abrasive grains bonded with resins and fillers and reinforced with glass fibre.

    Flap discs work differently. They consist of overlapping flaps of abrasive cloth. The zirconia grain breaks down in a controlled way during use, constantly creating new sharp cutting edges. As a result, performance remains consistent over the life of the disc. HILCO flap discs have a conical design on a fibre backing pad, intended for grinding at an angle of 15 to 25 degrees.

    The Hilblend blending disc is made of thick synthetic fibres with an extra coarse grain. The open structure cuts fast without clogging. The disc removes, levels and conditions in a single operation, without removing excessive base material.

    Typical applications

    • Removing surface rust, corrosion and mill scale with Hilblend
    • Removing light weld spatter and contamination without affecting the plate
    • Removing paint and epoxy coating in preparation for a next operation
    • Levelling welds and bevelling edges with a flap disc
    • Removing burrs after cutting

    What to consider when choosing

    Pay attention to the diameter, the thickness and the bore size, so that the disc fits your machine. Also check that the disc is suitable for the material you are working on. With stainless steel, it is important that the disc does not leave ferrous contamination, because that can later cause rust.

    Where the discs are used

    Abrasives are used in virtually every sector where metal is worked. In the petrochemical industry, the food industry, shipbuilding, construction and repair and maintenance, they are part of daily work. They are often used in combination with welding: first cutting, then welding, then levelling and finishing the weld.

    In hardfacing, a disc is even part of the process. The weld metal of hardfacing products is so hard that it can only be finished by grinding. Turning or milling is not possible. Allow for this in your work preparation.

    HILCO Hildiscs are produced in the Netherlands. The complete documentation can be found under abrasives documentation.

    We are happy to help you put together the right range of discs for your workshop.

    "
  2. How do you recognise a safe cutting disc?
    "

    A safe cutting disc complies with EN 12413 and preferably carries the oSa quality mark. The disc states the maximum permitted rotational speed, the dimensions, the application and the expiry date.

    The applicable standards

    DesignationWhat it means
    EN 12413European safety standard for bonded abrasives
    oSaQuality mark of the Organisation for the Safety of Abrasives
    ISO 9001Quality management system of the manufacturer
    Maximum speedThe highest permitted rotational speed of the disc
    Expiry dateBonded discs have a limited service life

    HILCO Hildiscs are produced in accordance with ISO 9001 and EN 12413 and meet the requirements of the Organisation for the Safety of Abrasives. This means that the discs are tested by an independent party and that requirements apply to the production, not only to the end product.

    Why this is not a formality

    A cutting disc runs at high speeds. If a disc breaks during use, the fragments are released at great speed. That is a real safety risk for the user and for everyone in the immediate vicinity. The standards and the glass fibre reinforcement in the disc are there to prevent this.

    What you will find on the disc itself

    All mandatory information is on the label of the disc. In addition to the standard and the quality mark, you will find the dimensions, the maximum speed, the material for which the disc is intended and the expiry date. Take the trouble to read that information before you mount the disc. It is the quickest check you can carry out and it takes a few seconds.

    Practical safety rules

    • Check the maximum speed on the disc against the speed of your machine
    • Always use the guard of the machine
    • Do not use a cutting disc for grinding, the side is not designed for this
    • Check the disc for cracks and damage before use
    • Store discs dry and flat, moisture and distortion affect the disc
    • Observe the expiry date

    What the quality mark says about the manufacturer

    A quality mark such as oSa tests not only the end product but also the way in which it is made. The manufacturer must demonstrate that its process is under control and is inspected on that basis periodically. That distinguishes certified discs from products chosen on price alone. For a product that runs at high speeds and is used close to the user's face, that is a relevant difference.

    Protecting the user

    Grinding and cutting release sparks, dust and particles. Eye protection, hearing protection and respiratory protection are therefore essential. Our range of personal protective equipment is designed for this.

    For us, safety is not an afterthought. That applies to the products we supply and to the way in which we advise on them.

    Do you have questions about the right disc for your machine? Contact us.

    "
Certificates
  • TUV.png
  • LR.png
  • ISO.png
  • DNV.png
  • CE.png
  • Bureau Veritas.png
  • AEO.png
  • ABS.png
Read more >
Receive our newsletter!

Sign up for the free newsletter to stay up to date

Quotation Shopping cart

Your shopping cart is still empty!

Add products from the catalog to place an order
Continue shopping
  • :
  • :
  • Total weight
Op voorraad
Not in stock
excl. VAT
Aanbevolen producten