Can I weld aluminium without shielding gas?

Yes. With the HILCO Aluminil electrodes, you weld aluminium with an ordinary electrode welding machine, without shielding gas and without a gas cylinder. For gas welding, there are also cored rods with an internal flux, which do not require a separate flux.

Why this is practical

MIG and TIG welding of aluminium requires a gas cylinder, a wire feeder and a suitable power source. For a repair in the field or on board a ship, that equipment is often not available. With a covered aluminium electrode, you only need a power source and an electrode holder. That makes emergency repairs to aluminium components possible on site as well.

The range

ProductClassificationIntended for
Aluminil Si5EN ISO 18273 E Al 4043Pure aluminium and AlMgSi alloys
Aluminil Si12EN ISO 18273 E Al 4047AlSi casting alloys up to 12 percent silicon
Fluxcored AlSi5Cored rodGas welding and surfacing, flux in the core
Fluxcored Al99.5Cored rodGas welding of pure aluminium

Aluminil Si12 has been developed specifically for welding AlSi casting alloys. The high silicon content improves the flow characteristics of the weld pool and reduces crack sensitivity. The colour of the weld metal closely matches aluminium castings, which matters for visible repairs.

Points of attention when welding

  • Clean the surface thoroughly, aluminium quickly forms an oxide layer
  • Store the electrodes dry, the special coating limits moisture absorption but does not rule it out
  • Take the high thermal conductivity of aluminium into account when setting your machine
  • When TIG welding, use the right tungsten electrode, which you can find among the accessories

Typical repairs

The Aluminil electrodes are used for engine blocks, cylinder heads, pump housings, machine beds and components in the maritime sector. They are products for repair work, not for series production. For production welding of aluminium, MIG or TIG remains the preferred route.

The electrodes are supplied in hermetically sealed aluminium tins, packed six to an outer box. This packaging keeps the product dry until the moment of use.

What you can expect

A covered aluminium electrode is a repair solution. The weld metal is soft and ductile with good mechanical properties, and the corrosion resistance is good. For production work, long continuous welds and structures with high requirements for appearance, MIG or TIG remains the preferred route.

Bear in mind that aluminium dissipates heat quickly. With thicker components, preheating is required to achieve good fusion. With thin parts, the risk is precisely that of burn-through, because aluminium does not change colour when heated and you therefore have little visual warning.

We are happy to think along with you about the approach to an aluminium repair.

Contact

Do you have a question? Feel free to contact us using this contact form!

  1. Which filler metal should I choose for welding aluminium?
    "

    The choice depends on the aluminium alloy. For AlMg alloys such as 5083 and 5086, choose AlMg5 or AlMg4.5Mn. For AlMgSi alloys such as 6060 and 6082 and for casting alloys containing silicon, choose AlSi5 or AlSi12. For pure aluminium, use Al99.7.

    First determine the alloy group

    Aluminium falls into three groups. Pure aluminium comes in purities from 99.0 to 99.7 percent. Non-heat-treatable alloys contain small amounts of manganese or magnesium, with AlMg alloys containing up to 5 percent magnesium being common. Heat-treatable alloys contain copper, magnesium with silicon, or zinc with magnesium.

    Pure aluminium and most non-heat-treatable and heat-treatable alloys are readily weldable. With heat-treatable alloys containing copper, however, there is a risk of hot cracking, which makes them difficult to weld. Casting alloys with a high copper or magnesium content are not always weldable either. So determine in advance which alloy you are dealing with.

    The range at a glance

    ProductAWSMaterial numberTypical application
    Al99.7A5.10 approx. ER11003.0259Pure aluminium, tanks and sheet metal work
    AlSi5A5.10 ER 40433.2245AlMgSi alloys, thin-walled work, frames
    AlSi12A5.10 ER 40473.2585Casting alloys up to 12 percent silicon, heat exchangers
    AlMg4.5MnA5.10 ER 51833.35485083, pressure vessels, tanks for liquefied gas
    AlMg5A5.10 ER 53563.35565086, 5454, 6061, shipbuilding and transport

    For most combinations of base materials, AlMg5 and AlSi5 are the starting point. If the component comes into contact with seawater or sea air, the AlMg grades are preferred because of their corrosion resistance.

    MIG or TIG

    The two dominant processes for aluminium are MIG and TIG. TIG is the better choice for thin-walled material, when there are requirements for the appearance of the weld, for single-sided welding such as on pipes, and for repair work. TIG welding of aluminium is usually done on alternating current. Use MIG for thicker materials and when speed matters in combination with long continuous welds.

    There are also versions for gas welding and for welding with covered electrodes. You will find these under brazing rods and stick electrodes.

    Where aluminium is used

    • Shipbuilding, in particular yachts, smaller vessels and specialised ships
    • Tanks and bodywork in transport and vehicle construction
    • Heat exchangers and pressure vessels
    • Repair of castings such as cylinder heads and pump housings

    Points of attention with aluminium

    • Remove the oxide layer just before welding, as it melts at a much higher temperature than the aluminium beneath it
    • Take the high thermal conductivity into account, you need more heat input than for steel of the same thickness
    • Aluminium does not change colour when heated, which makes burn-through difficult to see
    • Work cleanly and use a separate set of tools for aluminium

    For welding pure aluminium and casting alloys in repair work, Al99.7 is also available as a TIG rod. For components that will be anodised, the choice of filler metal affects the colour after anodising. Mention this in your enquiry and we will take it into account in our advice.

    The complete data sheets and safety data sheets can be found under aluminium documentation.

    We are happy to help you determine the right combination of alloy and filler metal.

    "
  2. Can I weld aluminium without shielding gas?
    "

    Yes. With the HILCO Aluminil electrodes, you weld aluminium with an ordinary electrode welding machine, without shielding gas and without a gas cylinder. For gas welding, there are also cored rods with an internal flux, which do not require a separate flux.

    Why this is practical

    MIG and TIG welding of aluminium requires a gas cylinder, a wire feeder and a suitable power source. For a repair in the field or on board a ship, that equipment is often not available. With a covered aluminium electrode, you only need a power source and an electrode holder. That makes emergency repairs to aluminium components possible on site as well.

    The range

    ProductClassificationIntended for
    Aluminil Si5EN ISO 18273 E Al 4043Pure aluminium and AlMgSi alloys
    Aluminil Si12EN ISO 18273 E Al 4047AlSi casting alloys up to 12 percent silicon
    Fluxcored AlSi5Cored rodGas welding and surfacing, flux in the core
    Fluxcored Al99.5Cored rodGas welding of pure aluminium

    Aluminil Si12 has been developed specifically for welding AlSi casting alloys. The high silicon content improves the flow characteristics of the weld pool and reduces crack sensitivity. The colour of the weld metal closely matches aluminium castings, which matters for visible repairs.

    Points of attention when welding

    • Clean the surface thoroughly, aluminium quickly forms an oxide layer
    • Store the electrodes dry, the special coating limits moisture absorption but does not rule it out
    • Take the high thermal conductivity of aluminium into account when setting your machine
    • When TIG welding, use the right tungsten electrode, which you can find among the accessories

    Typical repairs

    The Aluminil electrodes are used for engine blocks, cylinder heads, pump housings, machine beds and components in the maritime sector. They are products for repair work, not for series production. For production welding of aluminium, MIG or TIG remains the preferred route.

    The electrodes are supplied in hermetically sealed aluminium tins, packed six to an outer box. This packaging keeps the product dry until the moment of use.

    What you can expect

    A covered aluminium electrode is a repair solution. The weld metal is soft and ductile with good mechanical properties, and the corrosion resistance is good. For production work, long continuous welds and structures with high requirements for appearance, MIG or TIG remains the preferred route.

    Bear in mind that aluminium dissipates heat quickly. With thicker components, preheating is required to achieve good fusion. With thin parts, the risk is precisely that of burn-through, because aluminium does not change colour when heated and you therefore have little visual warning.

    We are happy to think along with you about the approach to an aluminium repair.

    "
Certificates
  • TUV.png
  • LR.png
  • ISO.png
  • DNV.png
  • CE.png
  • Bureau Veritas.png
  • AEO.png
  • ABS.png
Read more >
Receive our newsletter!

Sign up for the free newsletter to stay up to date

Quote list Shopping cart

Your quote list is still empty!

Add products from the catalog to place an order
Continue shopping
  • :
  • :
  • Totaal gewicht
Op voorraad
Not in stock
Aanbevolen producten