Which standards apply to personal protective equipment for welding?

For welding clothing, EN ISO 11611 applies, with class 2 being the higher level of protection. For gloves and mechanical protection, EN 388 applies. Welding helmets with an automatic welding filter are designated with a shade range for the darkness of the filter.

The standards in brief

StandardForWhat you need to know
EN ISO 11611Protective clothing for welding and allied processesClass 2 offers higher protection against riskier welding techniques and spatter
EN 388Mechanical protection of glovesThe figures indicate the resistance to abrasion, cutting, tearing and puncture
Welding filter shade numberDarkness of the welding filterThe higher the number, the darker the filter

Which class and which shade number you need depends on the welding process, the amperage and the conditions. At higher amperages, a darker filter is required. For processes with a lot of spatter, a higher clothing class is recommended.

What the range consists of

ProductMaterial or designProtects
SparkShield ADF welding helmetFour arc sensors, shade 9 to 13Eyes and face
SparkShield flip-up welding helmetFlip-up visorEyes and face
Welding glovesSplit cowhide leather, flannel linedHands and wrists
Welding jacketFlame retardantTorso and arms
Welding apronSplit cowhide leatherChest, torso and legs
Welding sleevesSplit cowhide leather with hook and loop fasteningForearms
Welding capFlame retardant cotton, reversibleHead and neck
Neck tubeFlame retardant cottonFace and neck

Why comfort counts

Protective equipment only works when it is actually worn. Clothing that pinches or gloves that take away the sense of touch are taken off or avoided in practice. That is why, when putting together the range, we look at both the level of protection and the fit and wearing comfort throughout a full working day.

The same applies to the welding helmet. A large viewing window and a fast-reacting filter make the work less tiring, allowing the welder to stay concentrated for longer.

Protection during and after welding

Welding remains a process in which the welder must protect himself properly. Radiation is released, heat is generated and fumes and spatter are produced. The extent to which this occurs depends on the process, the base material and the filler metal. So always consult the safety data sheet of the product you are using, as it states which substances are released and which measures apply.

Also think about the phase after welding. A freshly welded workpiece stays hot for a long time and slag can fly in all directions when chipped off. So keep your protection on until the work is actually finished and has cooled down.

What protection does not replace

Personal protection is the last step in the safety chain, not the first. Good fume extraction, a tidy workplace and the correct settings of the welding machine remain essential. For the specific risks of a product, always consult the associated safety data sheet under documentation.

We are happy to help you put together a complete protection package for your team.

Contact

Do you have a question? Feel free to contact us using this contact form!

  1. Which standards apply to personal protective equipment for welding?
    "

    For welding clothing, EN ISO 11611 applies, with class 2 being the higher level of protection. For gloves and mechanical protection, EN 388 applies. Welding helmets with an automatic welding filter are designated with a shade range for the darkness of the filter.

    The standards in brief

    StandardForWhat you need to know
    EN ISO 11611Protective clothing for welding and allied processesClass 2 offers higher protection against riskier welding techniques and spatter
    EN 388Mechanical protection of glovesThe figures indicate the resistance to abrasion, cutting, tearing and puncture
    Welding filter shade numberDarkness of the welding filterThe higher the number, the darker the filter

    Which class and which shade number you need depends on the welding process, the amperage and the conditions. At higher amperages, a darker filter is required. For processes with a lot of spatter, a higher clothing class is recommended.

    What the range consists of

    ProductMaterial or designProtects
    SparkShield ADF welding helmetFour arc sensors, shade 9 to 13Eyes and face
    SparkShield flip-up welding helmetFlip-up visorEyes and face
    Welding glovesSplit cowhide leather, flannel linedHands and wrists
    Welding jacketFlame retardantTorso and arms
    Welding apronSplit cowhide leatherChest, torso and legs
    Welding sleevesSplit cowhide leather with hook and loop fasteningForearms
    Welding capFlame retardant cotton, reversibleHead and neck
    Neck tubeFlame retardant cottonFace and neck

    Why comfort counts

    Protective equipment only works when it is actually worn. Clothing that pinches or gloves that take away the sense of touch are taken off or avoided in practice. That is why, when putting together the range, we look at both the level of protection and the fit and wearing comfort throughout a full working day.

    The same applies to the welding helmet. A large viewing window and a fast-reacting filter make the work less tiring, allowing the welder to stay concentrated for longer.

    Protection during and after welding

    Welding remains a process in which the welder must protect himself properly. Radiation is released, heat is generated and fumes and spatter are produced. The extent to which this occurs depends on the process, the base material and the filler metal. So always consult the safety data sheet of the product you are using, as it states which substances are released and which measures apply.

    Also think about the phase after welding. A freshly welded workpiece stays hot for a long time and slag can fly in all directions when chipped off. So keep your protection on until the work is actually finished and has cooled down.

    What protection does not replace

    Personal protection is the last step in the safety chain, not the first. Good fume extraction, a tidy workplace and the correct settings of the welding machine remain essential. For the specific risks of a product, always consult the associated safety data sheet under documentation.

    We are happy to help you put together a complete protection package for your team.

    "
  2. Which welding helmet should I choose, automatic or flip-up?
    "

    Choose an automatic welding helmet with a welding filter if you weld regularly and in varying conditions. Choose a flip-up welding helmet if you weld occasionally or if you want to be able to grind and inspect frequently between welds without taking off the helmet.

    The difference

    FeatureSparkShield ADFSparkShield flip-up
    OperationFilter darkens automatically when the arc is struckVisor flipped up and down manually
    SensorsFour arc sensorsNot applicable
    Shade range9 to 13, adjustableFixed glass, shade 10
    Field of viewLarge field of viewMore limited
    Suitable forRegular welding, varying amperagesOccasional welding, alternating welding and grinding

    Why an automatic filter is pleasant to work with

    With a fixed glass, you have to lower the helmet each time before you strike the arc. That takes time and positioning the electrode is then done by feel. An automatic filter stays clear until the moment the arc is struck, after which it darkens within a fraction of a second. You therefore see your workpiece until just before the arc is struck.

    The adjustable shade range of 9 to 13 makes it possible to adapt the darkness to the process and the amperage. When TIG welding at low current, you work with a lighter setting than when welding with thick electrodes at high current.

    Maintenance and replacement parts

    The protective lenses in front of and behind the filter are consumables. They catch spatter and become dull over time. Replace them in good time, because a dull lens reduces visibility and therefore the quality of your work. Separate protective lenses for both helmet types can be found among the accessories.

    • Check before use that the filter darkens correctly
    • Replace scratched or fogged protective lenses
    • Store the helmet in a dry environment, out of direct sunlight
    • Clean the helmet with a soft cloth, do not use solvents

    Protection is more than the helmet

    A welding helmet protects the eyes and face against radiation, heat and spatter. The neck, arms, torso and hands require their own protection. So combine the helmet with gloves, a welding jacket or welding apron and, where necessary, welding sleeves and a neck tube.

    When a flip-up is practical

    A flip-up helmet has a hinged visor with a fixed welding glass. If you flip the visor up, you look through a clear protective lens and can grind, measure and inspect without taking off the helmet. For work in which you constantly alternate between welding and finishing, that is convenient. It is also a practical choice as a second helmet for occasional use or for visitors.

    We are happy to advise you on the right combination of protection for your welding process.

    "
Certificates
  • TUV.png
  • LR.png
  • ISO.png
  • DNV.png
  • CE.png
  • Bureau Veritas.png
  • AEO.png
  • ABS.png
Read more >
Receive our newsletter!

Sign up for the free newsletter to stay up to date

Quote list Shopping cart

Your quote list is still empty!

Add products from the catalog to place an order
Continue shopping
  • :
  • :
  • Totaal gewicht
Op voorraad
Not in stock
Aanbevolen producten