What do the letters R, W and G in the HILCHROME names mean?

The letter indicates the welding process for which the product is intended. A name ending in R stands for a covered electrode, a name beginning with W stands for a TIG rod and a name beginning with G stands for a MIG wire.

The system in brief

DesignationWelding processExample
Ends in RCovered electrode, also known as stick welding, MMA or SMAWHilchrome 316R
Begins with WTIG rod, also known as GTAWHilchrome W316L
Begins with GMIG wire, also known as GMAWHilchrome G316LSi

The number in the name refers to the alloy class and corresponds to the AISI designation of the base material. Hilchrome 316R, W316L and G316LSi are therefore three versions of the same alloy, intended for three different welding processes.

Why this is practical

Once you know which steel grade you are welding, you only need to determine which process you are working with. The rest of the product name stays the same. That makes it easier to switch process within a project without losing sight of the alloy.

In practice, this happens often. Pipes are usually TIG welded because they are thin-walled and the first pass must be clean and sealed. After that, they are often completed with MIG because it is faster. You then use W316L for the root pass and G316LSi for the fill passes, within the same alloy class.

Where else you will come across the letters

  • Products with HARDMELT in the name are hardfacing electrodes
  • Products with FER in the name are solid wires for unalloyed and low-alloy steel
  • Products with HILCORD in the name are cored wires
  • Products beginning with a B are basic covered electrodes for low-alloy steel
  • Products with CHROMO or CrMo in the name are creep resistant and intended for elevated temperatures

The addition L in a name such as W316L or G308LSi stands for a low carbon content. The addition Si indicates an increased silicon content, which improves the flow characteristics of the weld pool.

Why the designations are used interchangeably

In data sheets, standards and conversations, you will come across several terms for the same process. Covered electrodes are referred to as stick welding, MMA, SMAW or simply electrode welding. MIG and MAG together fall under GMAW, TIG under GTAW. These terms all refer to the same process, but come from different systems of standards and language areas. Our product pages always state the process for which the product is intended, so you do not need to translate between those systems.

The full classification according to AWS and EN can be found on every product page and on the associated data sheet. The brand name and classification are printed on the coating of the electrode itself.

We are happy to help you translate a classification into the right product.

Contact

Do you have a question? Feel free to contact us using this contact form!

  1. Which welding consumable should I choose for stainless steel?
    "

    Choose the filler metal that matches the stainless steel grade you are welding. For AISI 304 and 304L use the 308 grade, for AISI 316 and 316L the 316 grade, and for the stabilised types 321 and 347 the 347 grade.

    Why matching welding is particularly important here

    Stainless steel owes its corrosion resistance to chromium. Nickel is added to keep the material readily weldable. If the material must withstand more acidic media or higher temperatures, molybdenum is added. This composition determines what a steel grade can withstand.

    If, for example, you weld a pipe that carries milk, fruit juice or a chemical medium, the welded joint must have the same resistance as the rest of the pipe. A weld with a lower alloy content becomes the weak point in the installation. In an environment where sulphuric acid is pumped, higher demands are placed on the material than in a dairy plant. So first identify the base material and then find the matching product.

    The HILCHROME range by steel grade

    Base materialCovered electrodeMIG wireTIG rod
    AISI 304, 304L, 308LHilchrome 308RG308LSiW308L
    AISI 316, 316LHilchrome 316RG316LSiW316L
    AISI 321, 347, 348Hilchrome 347ROn requestOn request
    AISI 309, heat-resistant CrNiHilchrome 309RG309LSiW309L
    AISI 310, 310SHilchrome 310ROn requestOn request
    Dissimilar and difficult to weldHilchrome 312RG307On request

    Special cases

    • For joining dissimilar steels and for buffer layers, choose Hilchrome 307R or Hilchrome 312R
    • For armoured and clad plates, Hilchrome 309MoR is suitable thanks to its increased ferrite content
    • For ferritic chromium steels such as 410, 430 and 431, use 308, 309 or 310 grades

    The welding process determines the form

    Within an alloy class, you choose the version that suits your welding process. Pipes are often TIG welded because of their small wall thickness, after which they are completed with MIG or covered electrodes. If you work outdoors or in a place that is difficult to reach, a gas-shielded process is ruled out and you use a covered electrode. For that reason, many stainless steel joints in the process industry are still made with HILCHROME electrodes.

    With stainless steel, also pay attention to your tools. Use separate brushes and discs, so that no iron particles remain on the surface. Those particles can later cause rust on an installation that is itself stainless.

    Packaging and storage

    HILCHROME electrodes are supplied in hermetically sealed metal tins. This packaging keeps the electrodes dry in the same condition as immediately after production and protects against climate changes and moisture absorption. When used within an eight-hour working day, this produces weld metal free of porosity, regardless of the climate.

    The data sheets and safety data sheets can be found under stainless steel documentation.

    You know the steel grade but are unsure about the combination with your process? Contact us for advice.

    "
  2. What do the letters R, W and G in the HILCHROME names mean?
    "

    The letter indicates the welding process for which the product is intended. A name ending in R stands for a covered electrode, a name beginning with W stands for a TIG rod and a name beginning with G stands for a MIG wire.

    The system in brief

    DesignationWelding processExample
    Ends in RCovered electrode, also known as stick welding, MMA or SMAWHilchrome 316R
    Begins with WTIG rod, also known as GTAWHilchrome W316L
    Begins with GMIG wire, also known as GMAWHilchrome G316LSi

    The number in the name refers to the alloy class and corresponds to the AISI designation of the base material. Hilchrome 316R, W316L and G316LSi are therefore three versions of the same alloy, intended for three different welding processes.

    Why this is practical

    Once you know which steel grade you are welding, you only need to determine which process you are working with. The rest of the product name stays the same. That makes it easier to switch process within a project without losing sight of the alloy.

    In practice, this happens often. Pipes are usually TIG welded because they are thin-walled and the first pass must be clean and sealed. After that, they are often completed with MIG because it is faster. You then use W316L for the root pass and G316LSi for the fill passes, within the same alloy class.

    Where else you will come across the letters

    • Products with HARDMELT in the name are hardfacing electrodes
    • Products with FER in the name are solid wires for unalloyed and low-alloy steel
    • Products with HILCORD in the name are cored wires
    • Products beginning with a B are basic covered electrodes for low-alloy steel
    • Products with CHROMO or CrMo in the name are creep resistant and intended for elevated temperatures

    The addition L in a name such as W316L or G308LSi stands for a low carbon content. The addition Si indicates an increased silicon content, which improves the flow characteristics of the weld pool.

    Why the designations are used interchangeably

    In data sheets, standards and conversations, you will come across several terms for the same process. Covered electrodes are referred to as stick welding, MMA, SMAW or simply electrode welding. MIG and MAG together fall under GMAW, TIG under GTAW. These terms all refer to the same process, but come from different systems of standards and language areas. Our product pages always state the process for which the product is intended, so you do not need to translate between those systems.

    The full classification according to AWS and EN can be found on every product page and on the associated data sheet. The brand name and classification are printed on the coating of the electrode itself.

    We are happy to help you translate a classification into the right product.

    "
  3. Which electrode do I use if I do not know which steel I am welding?
    "

    In that case, use HILCO Hilchrome 312R. This rutile covered electrode is designed as a problem solver for virtually all steel grades, including stainless steel and steels that are difficult to weld, and is the safe choice when the composition of the base material is unknown.

    When this situation arises

    It regularly happens that a component breaks whose composition nobody knows. The certification is missing, the drawing no longer exists, or the component was once purchased elsewhere. Yet welding must be done, because something has come to a standstill.

    As long as you can establish that the material is ferrous, so steel, cast steel or cast iron, and not copper or aluminium, you can use Hilchrome 312R. The electrode works on all steel grades, hardened or not.

    What this electrode can do

    PropertyWhat that means
    AWS A5.4 approx. E312-17High-alloy rutile covered electrode
    High ferrite contentCrack-resistant weld metal
    Wide range of applicationsStructural steel, tool steel, manganese steel, spring steel, armour plate
    Suitable for buffer layersCan be applied before hardfacing
    All welding positionsAlso usable in places that are difficult to reach
    AC and DCWorks on both alternating current and direct current

    The electrode is also pleasant to use. The arc is easy to control and even a less experienced welder can achieve a usable result with it. That is exactly what you are looking for in a situation that requires fast action.

    Weighing it up

    Hilchrome 312R is a relatively expensive product. On the other hand, a single electrode covers a large proportion of possible repairs. You need to keep fewer different products in stock and the chance of making the wrong choice becomes small. In a critical repair, that outweighs the price per kilo, especially when the wrong electrode would make the problem bigger or irreparable.

    For that reason, many factories keep a stock of 312R as an emergency provision, alongside the products they use every day. That applies to a sugar factory just as much as to a ship or a petrochemical company.

    Use matching welding wherever possible

    This electrode is a solution for unknown situations, not a replacement for proper material identification. If you do know which material you are welding, first determine the steel grade and then find the matching filler metal. That provides the best match with the properties of the base material.

    Read more about this trade-off in our article what if you do not know which steel you are welding. Cast iron requires its own approach, which you can find under welding of cast iron.

    In doubt about a repair on an unknown material? Contact us and we will think along with you.

    "
  4. Why is the root pass welded with TIG and then completed with MIG?
    "

    The root pass is welded with TIG because that process provides clean, sealed penetration. For the fill passes, the welder switches to MIG because that process is faster. This way, you combine the quality of TIG with the productivity of MIG.

    What each process does well

    In TIG welding, the welder has a great deal of control over the weld pool and the heat input. That is exactly what you need for the first pass of a pipe joint, where the weld must penetrate the full wall thickness and the inside must remain smooth. For thin-walled material, TIG is the preferred process for the same reason.

    Once the root pass is in place, the task changes. The joint has to be filled, and that should be done as efficiently as possible. MIG welding deposits more material per unit of time and works continuously from a spool, without the interruptions that do occur with electrodes. For the fill passes, that is the logical choice.

    Which products to use

    PassProcessProduct for 316 gradeProduct for 308 grade
    Root passTIGHilchrome W316LHilchrome W308L
    Fill passesMIGHilchrome G316LSiHilchrome G308LSi
    Alternative, all passesCovered electrodeHilchrome 316RHilchrome 308R

    It is important to stay within the same alloy class. When you switch process, you change the form of the filler metal, not the chemical composition.

    When you do use electrodes

    Covered electrodes are still widely used in the process industry. If you work outdoors, or if the location is difficult to reach for a wire feeder, a gas-shielded process is ruled out. Stainless steel joints are then simply welded with a HILCHROME electrode.

    The scale of the work also plays a role. For a few centimetres of weld on a small crack, you do not haul in a wire feeder and a gas cylinder. For a boiler or series production, on the other hand, you do choose a mechanised process, because an electrode costs too many man-hours there.

    Points of attention for the combination

    • Clean the root pass before you start filling
    • Monitor the interpass temperature in accordance with the welding procedure
    • With stainless steel, use a separate set of tools to prevent iron contamination
    • Check that the choice of gas suits the process and the alloy

    The choice of welding process is ultimately a decision for the designer or the responsible welder on site. We make sure that a suitable filler metal is available for each of these processes.

    Why this is a question of productivity

    The underlying consideration is always the same: where do you need control and where do you need speed. For the root pass, the quality of the penetration counts, because it determines whether the joint is sealed across the full wall thickness. For the fill passes, what counts is the amount of material you deposit per hour. By choosing the appropriate process for each pass, you get the most out of both without compromising the quality of the joint.

    We are happy to help you put together the right combination for your welding procedure.

    "
Certificates
  • TUV.png
  • LR.png
  • ISO.png
  • DNV.png
  • CE.png
  • Bureau Veritas.png
  • AEO.png
  • ABS.png
Read more >
Receive our newsletter!

Sign up for the free newsletter to stay up to date

Quote list Shopping cart

Your quote list is still empty!

Add products from the catalog to place an order
Continue shopping
  • :
  • :
  • Totaal gewicht
Op voorraad
Not in stock
Aanbevolen producten