Which welding electrode do I use for welding pipelines?

For joining pipelines, use HILCO Pipeweld 6010 or Pipeweld 7010. These are cellulosic covered electrodes with a deeply penetrating, forceful arc, specifically designed for vertical down welding of pipe joints in the field.

Why pipelines require a dedicated electrode

Pipelines for oil, gas and water are almost always welded outdoors. The welder works in the open air, often under a small tent to keep out the wind. There is no workshop, no gas cylinder and little room to manoeuvre. In addition, the first pass must achieve full penetration, so that the joint is sealed across the entire wall thickness.

That calls for an electrode with a high degree of penetration and an arc that is easy to control in the vertical down direction. A standard rutile electrode does not meet those requirements. The Pipeweld range has been developed precisely for this work.

The difference between the two versions

ProductAWSIntended for
Pipeweld 6010A5.1 E 6010All positions, in particular vertical down and overhead
Pipeweld 7010A5.5 E 7010-P1Butt welds in high-strength steel pipe, vertical down

In short: 6010 is the broad choice for pipework in unalloyed steel, 7010 is intended for pipe with a higher strength class. In both cases the slag is easy to remove, which saves time when working in the field.

Packaging is not a detail here

Cellulosic covered electrodes need a certain moisture content to work properly. That is why Pipeweld electrodes are supplied in metal tins instead of cardboard boxes. This packaging maintains the moisture level required for correct performance. Keep the tins closed and in a dry place.

Applications in practice

  • Laying and extending transport pipelines for oil, gas and water
  • Connecting pipelines between platform, storage and processing
  • Repairing existing pipeline sections in the field
  • Smaller and local pipeline projects that require a fast turnaround

In the oil and gas chain, welding takes place at every stage: during extraction, in distribution, in storage and in refining. The structural side of this sector also requires products from the unalloyed steel and low-alloy steel ranges. Read more about these applications on our oil and gas page.

Where pressure and temperature are not the issue

In oil pipelines, pressure and temperature play a limited role, because the product is transported at ambient temperature. The requirements here relate to weldability in the field and to the penetration of the joint. That is a different matter from boilers and steam pipes, where heat-resistant properties are indeed required. For those applications, look at the creep-resistant products in the low-alloy steel range.

The data sheets and safety data sheets for the Pipeweld range can be found under unalloyed steel documentation.

We are happy to think along with you about the right electrode for your pipework.

Contact

Do you have a question? Feel free to contact us using this contact form!

  1. Which welding electrode should I choose for unalloyed steel?
    "

    For simple steelwork without special requirements, choose a rutile covered electrode such as HILCO Red Extra. If there are requirements for strength, toughness or impact toughness at low temperature, choose a basic covered, low-hydrogen electrode such as HILCO Basic or HILCO Basic Super.

    Rutile or basic

    The difference lies in the coating. Rutile covered electrodes are easy to use, strike easily, weld smoothly and leave a slag that is easy to remove. They are suitable for structural work where one electrode type is sufficient. Basic covered electrodes produce low-hydrogen weld metal, which limits the risk of hydrogen cracking. They deliver better mechanical properties, also at low temperature, and are therefore the choice for thicker plates and heavier structures.

    The range at a glance

    ProductAWSCharacterTypical application
    Red ExtraA5.1 E 6013Rutile, all positions incl. vertical downGeneral steelwork, repair and maintenance
    BasicA5.1 E 7018-1Low hydrogen, down to -50 degrees CelsiusStructural work with toughness requirements
    Basic SuperA5.1 E 7018-1Low hydrogen, down to -40 degrees Celsius, AC and DCStructural work on varying power sources
    Basic 55A5.1 E 7016Double coated basic-rutile, down to -30 degrees CelsiusRoot passes and full penetration
    VelvetaA5.1 E 6013Smooth, vertical up, AC and DCSmall diameter pipes, X-ray quality
    VeloraA5.1 E 6013Spatter-free, flat positionThin sheet
    BrownA5.1 E 6013Fast freezing, vertical downRusty, painted or contaminated steel
    E6011A5.1 E 6011Deep penetration, forceful arcContaminated, rusty or galvanised material
    Regina 150 and 160A5.1 E 7024-1High efficiency, 160 percent recoveryFillet welds in the flat position

    What to consider when choosing

    • The welding position. Not every electrode is suitable for vertical down welding
    • The condition of the material. On rusty or painted steel, Brown and E6011 perform better
    • The type of current of your welding machine. Some types only work on direct current
    • The impact toughness requirement. If your specification calls for values at low temperature, choose low hydrogen
    • The plate thickness. Thicker plates require more toughness in the weld metal

    Why ease of use counts

    An electrode that strikes easily, produces little spatter and leaves a self-releasing slag saves the welder finishing work. That is not a minor detail. A welder who enjoys working with the material works with more concentration and lays down more metres per day. So it is not only about the mechanical properties on paper, but also about how the product behaves in the welder's hand.

    All data sheets and safety data sheets for these products can be found under unalloyed steel documentation.

    We are happy to help you choose the right product for your application.

    "
  2. What is the difference between HILCO Basic and HILCO Basic Super?
    "

    Both are low-hydrogen electrodes of type AWS A5.1 E 7018-1 for structural work. The practical difference lies in the power source: Basic Super works on both alternating current and direct current, while Basic is the targeted choice when you know for certain that you will be welding with direct current.

    The power source is decisive

    In the past, a lot of welding was done with transformers on alternating voltage. That is an inexpensive, low-maintenance way of welding that worked well for many years. Modern companies work with direct current, generated by rectifiers or inverters. This equipment is lighter, more compact and delivers a more stable arc.

    Basic Super is formulated to work on both types of current. That broader applicability makes the product somewhat more expensive. If you work exclusively with direct current, Basic is the more targeted choice for that specific purpose. So it is not a question of better or worse, but of matching the equipment in your workshop.

    The technical differences

    FeatureBasicBasic Super
    AWS classificationA5.1 E 7018-1A5.1 E 7018-1
    Type of currentDirect currentAlternating current and direct current
    Mechanical properties down to-50 degrees Celsius-40 degrees Celsius
    Welding positionsAll, except vertical downAll, except vertical down
    Diameters2.5 to 6.0 millimetres2.5 to 5.0 millimetres
    Arc characteristicsSmooth, very little spatterEasy to control

    What both products have in common

    Both are low-hydrogen electrodes. Hydrogen in the weld metal, in combination with stresses in the structure, is the main cause of cold cracking, also known as hydrogen cracking or delayed cracking. By keeping the hydrogen content low, you reduce that risk considerably.

    You further reduce the risk of cold cracking by preheating the base material, keeping the weld joint clean and dry and limiting shrinkage stresses. Basic electrodes absorb moisture from the air, so the way you store them affects the result. The guidelines for this can be found under handling, storage and drying.

    When to choose one or the other

    • Choose Basic Super when several welding machines are in use or when the power source differs per location
    • Choose Basic when the workshop runs entirely on direct current
    • Choose Basic when the specification calls for values at temperatures below -40 degrees Celsius
    • Consider Basic 55 when you mainly weld root passes and value full penetration

    Where you will come across both

    Basic and Basic Super are used for structural work on thicker plates where requirements are set for toughness and strength. You will find them in steel construction, pressure equipment, the structural side of the petrochemical industry and heavier repairs. They are also widely used for welding pipe joints in the oil and gas chain, where the choice between the two types is usually made locally based on the available equipment.

    The exact type of current, polarity and recommended amperage per diameter are stated on the product data sheet.

    Not sure which power source you have? We are happy to think along with you.

    "
  3. Which welding electrode do I use for welding pipelines?
    "

    For joining pipelines, use HILCO Pipeweld 6010 or Pipeweld 7010. These are cellulosic covered electrodes with a deeply penetrating, forceful arc, specifically designed for vertical down welding of pipe joints in the field.

    Why pipelines require a dedicated electrode

    Pipelines for oil, gas and water are almost always welded outdoors. The welder works in the open air, often under a small tent to keep out the wind. There is no workshop, no gas cylinder and little room to manoeuvre. In addition, the first pass must achieve full penetration, so that the joint is sealed across the entire wall thickness.

    That calls for an electrode with a high degree of penetration and an arc that is easy to control in the vertical down direction. A standard rutile electrode does not meet those requirements. The Pipeweld range has been developed precisely for this work.

    The difference between the two versions

    ProductAWSIntended for
    Pipeweld 6010A5.1 E 6010All positions, in particular vertical down and overhead
    Pipeweld 7010A5.5 E 7010-P1Butt welds in high-strength steel pipe, vertical down

    In short: 6010 is the broad choice for pipework in unalloyed steel, 7010 is intended for pipe with a higher strength class. In both cases the slag is easy to remove, which saves time when working in the field.

    Packaging is not a detail here

    Cellulosic covered electrodes need a certain moisture content to work properly. That is why Pipeweld electrodes are supplied in metal tins instead of cardboard boxes. This packaging maintains the moisture level required for correct performance. Keep the tins closed and in a dry place.

    Applications in practice

    • Laying and extending transport pipelines for oil, gas and water
    • Connecting pipelines between platform, storage and processing
    • Repairing existing pipeline sections in the field
    • Smaller and local pipeline projects that require a fast turnaround

    In the oil and gas chain, welding takes place at every stage: during extraction, in distribution, in storage and in refining. The structural side of this sector also requires products from the unalloyed steel and low-alloy steel ranges. Read more about these applications on our oil and gas page.

    Where pressure and temperature are not the issue

    In oil pipelines, pressure and temperature play a limited role, because the product is transported at ambient temperature. The requirements here relate to weldability in the field and to the penetration of the joint. That is a different matter from boilers and steam pipes, where heat-resistant properties are indeed required. For those applications, look at the creep-resistant products in the low-alloy steel range.

    The data sheets and safety data sheets for the Pipeweld range can be found under unalloyed steel documentation.

    We are happy to think along with you about the right electrode for your pipework.

    "
Certificates
  • TUV.png
  • LR.png
  • ISO.png
  • DNV.png
  • CE.png
  • Bureau Veritas.png
  • AEO.png
  • ABS.png
Read more >
Receive our newsletter!

Sign up for the free newsletter to stay up to date

Quote list Shopping cart

Your quote list is still empty!

Add products from the catalog to place an order
Continue shopping
  • :
  • :
  • Totaal gewicht
Op voorraad
Not in stock
Aanbevolen producten