How do I choose the right welding consumable for my application?

You select the welding consumable based on three factors: the base material you are welding, the welding process you use and the conditions under which the structure will have to perform. The starting point is matching welding, where the filler metal corresponds to the base material in composition and properties.

Start with the base material

The first question is always which material lies beneath the weld. Unalloyed steel, low-alloy steel, stainless steel, aluminium and non-ferrous metals each have their own requirements. For a stainless steel pipeline, you look for a filler metal with a comparable chemical composition, so that the welded joint retains the same corrosion resistance as the rest of the installation. For cast iron, on the other hand, you work with nickel-based products, because matching welding is not possible there.

Identifying the base material is the job of the designer, the welder or the person responsible on site. If the steel grade is stated on the drawing or the certificate, the choice is usually quickly made. If that information is missing, read the question on welding without knowing the material.

Then determine the welding process

The welding process determines the form of the filler metal. For covered electrodes, you choose from the stick electrodes range; for mechanised welding, from the MIG/MAG wires or the TIG rods. For gas welding and brazing, there is the brazing rods range.

The working environment plays a part in this. Gas-shielded processes are difficult to use outdoors, because the wind blows the shielding gas away. If you are working outdoors, a covered electrode is the obvious choice. In a workshop or assembly hall, a wire process is usually the logical choice.

Finally, consider the load in service

A welded joint must do what the structure demands of it. Relevant questions are: is the component under pressure, does it operate at elevated temperature, does it come into contact with acids or abrasive media, and are there requirements for impact toughness at low temperature? These requirements guide the choice within a material group. For components that operate at high temperature for long periods, choose creep-resistant products from the low-alloy steel range. For components subject to wear, choose hardfacing products.

What you want to knowWhere to find it
Chemical composition and mechanical propertiesThe product data sheet
Safe handling and fume extractionThe safety data sheet
Measured values per production batchThe material test certificate
Storage, drying and re-dryingHandling, storage and drying

All data sheets and safety data sheets are collected under documentation. If you are unsure how to read a data sheet, see the explanation of a typical data sheet.

In doubt about the combination of base material, welding process and application? Contact us for advice.

Contact

Do you have a question? Feel free to contact us using this contact form!

  1. How do I choose the right welding consumable for my application?
    "

    You select the welding consumable based on three factors: the base material you are welding, the welding process you use and the conditions under which the structure will have to perform. The starting point is matching welding, where the filler metal corresponds to the base material in composition and properties.

    Start with the base material

    The first question is always which material lies beneath the weld. Unalloyed steel, low-alloy steel, stainless steel, aluminium and non-ferrous metals each have their own requirements. For a stainless steel pipeline, you look for a filler metal with a comparable chemical composition, so that the welded joint retains the same corrosion resistance as the rest of the installation. For cast iron, on the other hand, you work with nickel-based products, because matching welding is not possible there.

    Identifying the base material is the job of the designer, the welder or the person responsible on site. If the steel grade is stated on the drawing or the certificate, the choice is usually quickly made. If that information is missing, read the question on welding without knowing the material.

    Then determine the welding process

    The welding process determines the form of the filler metal. For covered electrodes, you choose from the stick electrodes range; for mechanised welding, from the MIG/MAG wires or the TIG rods. For gas welding and brazing, there is the brazing rods range.

    The working environment plays a part in this. Gas-shielded processes are difficult to use outdoors, because the wind blows the shielding gas away. If you are working outdoors, a covered electrode is the obvious choice. In a workshop or assembly hall, a wire process is usually the logical choice.

    Finally, consider the load in service

    A welded joint must do what the structure demands of it. Relevant questions are: is the component under pressure, does it operate at elevated temperature, does it come into contact with acids or abrasive media, and are there requirements for impact toughness at low temperature? These requirements guide the choice within a material group. For components that operate at high temperature for long periods, choose creep-resistant products from the low-alloy steel range. For components subject to wear, choose hardfacing products.

    What you want to knowWhere to find it
    Chemical composition and mechanical propertiesThe product data sheet
    Safe handling and fume extractionThe safety data sheet
    Measured values per production batchThe material test certificate
    Storage, drying and re-dryingHandling, storage and drying

    All data sheets and safety data sheets are collected under documentation. If you are unsure how to read a data sheet, see the explanation of a typical data sheet.

    In doubt about the combination of base material, welding process and application? Contact us for advice.

    "
  2. When do I choose a welding electrode and when a welding wire?
    "

    Choose a welding wire where you can and a covered electrode where you must. Wire processes work continuously and are therefore more productive, but they need gas shielding and are hardly usable outdoors. Covered electrodes work anywhere, including outdoors and in places that are difficult to reach.

    The difference in practice

    A covered electrode is about 350 millimetres long. Once it has burned down, the welder has to stop, remove the stub from the electrode holder and insert a new electrode. Each change takes a number of seconds. A welding wire comes on a spool of 5 to 16 kilos and is fed continuously, which eliminates those interruptions. In a workshop where series are produced, that difference adds up.

    On the other hand, MIG, MAG and TIG work with a shielding gas. Outdoors, the wind blows the gas shield away, making the weld porous. A covered electrode creates its own protection through its coating and does not have that problem. For repairs in the field, on machines that cannot be brought indoors, the electrode therefore remains the practical choice.

    SituationPreferenceWhy
    Series production in a hallWelding wireContinuous process, no stops to change electrodes
    Repair in the fieldCovered electrodeNo gas shielding required
    Thin-walled work and root passesTIG rodControlled, clean result
    Thick plates, high deposition rateMIG/MAG wireHigh productivity
    Positions that are difficult to reachCovered electrodeCompact equipment, no gas hose
    Varied, unknown jobsCovered electrodeVersatile range

    What this means for your product range

    Many companies need both. A sugar factory or food processing company welds rollers and components indoors with wire, but repairs harvesting and transport machinery outdoors with electrodes. The same application then calls for two versions of the same product concept. Hardfacing is an example of this, which we supply both as electrodes and in wire form.

    When making your choice, also take the available equipment into account. Wire welding requires a wire feeder, a gas cylinder and a suitable power source. Electrode welding only requires a power source and an electrode holder. At locations where the equipment needs to stay simple, that is a decisive argument.

    Terms you will come across

    • Covered electrode welding is also referred to as stick welding, MMA or SMAW
    • MIG/MAG welding is referred to as GMAW, TIG welding as GTAW
    • Flux-cored wires are referred to as FCAW, metal-cored wires as MCAW

    These terms refer to the same process and are used interchangeably in data sheets and standards. Our product pages always state the process for which the product is intended.

    We are happy to help you determine the right combination of process and product for your workshop.

    "
  3. Why are certified welding consumables important?
    "

    In critical structures, the entire chain must be demonstrably in order, from the base material to the welding consumable and the qualification of the welder. Approval by an independent classification society closes that chain and establishes responsibility.

    When certification is mandatory

    As soon as the failure of a structure could endanger lives, strict requirements apply. Think of a bridge, a crane, a pressure vessel, a grandstand or a ship's hull. In the design phase, the engineer must already take into account the requirement that the welding consumables carry an official approval. If you use products that have not been approved, you run the risk of the entire structure being rejected.

    In Europe, this is regulated through CE marking. The associated standards are monitored by bodies that operate independently of the manufacturer.

    Which bodies carry out these checks

    BodyUsed for
    Lloyd's RegisterShipbuilding and maritime structures
    ABSShipbuilding and offshore
    DNVShipbuilding, offshore and industry
    TUVPressure and structural applications

    The chain must be complete

    This is most clearly visible in shipbuilding. No ship is built with electrodes or wires that have not been approved by an independent inspection body. If you nevertheless use products that have not been tested or approved, the ship itself will not be approved either. The same logic applies to other critical structures: the steel, the fasteners, the welding consumables and the qualification of the welder must all be demonstrably in order. If one link is missing, the chain is not complete.

    This also has a legal side. If a designer chooses a brand that has been approved by an independent party, responsibility on that point is covered. Should something go wrong after all, it can be demonstrated that the right choices were made at every point in the process.

    These societies do not only approve the end product. They also inspect the preceding process and the factories where production takes place. The approvals are reassessed at fixed intervals, making it not a one-off action but an ongoing obligation.

    What you receive from us

    For products intended for critical applications, we supply a quality certificate. It states what we measured before the product was packed: the chemical composition, the expected hardness, the toughness and the strength. This allows you to demonstrate that the filler metal matches the base material you are welding. Read more about this under material test certificates.

    Our abrasives are standardised as well. The Hilco Hildiscs are produced in accordance with ISO 9001 and EN 12413 and meet the requirements of the Organisation for the Safety of Abrasives.

    Weighing up the costs

    A certified electrode may cost slightly more per kilo than an uncertified alternative. Compare that difference with the costs incurred when a structure is rejected, a repair has to be redone or damage occurs. So do not only look at the price per kilo, but at the total cost of the application, including the consequences if something goes wrong.

    A more detailed discussion of this topic can be found in our article why certified welding consumables matter for critical constructions.

    Do you need certificates for a specific project? Contact us and we will find out which approvals apply to your application.

    "
Certificates
  • TUV.png
  • LR.png
  • ISO.png
  • DNV.png
  • CE.png
  • Bureau Veritas.png
  • AEO.png
  • ABS.png
Read more >
Receive our newsletter!

Sign up for the free newsletter to stay up to date

Quote list Shopping cart

Your quote list is still empty!

Add products from the catalog to place an order
Continue shopping
  • :
  • :
  • Totaal gewicht
Op voorraad
Not in stock
Aanbevolen producten